Distributed Temperature Sensing Systems (DTS) are optoelectronic devices which measure temperatures by means of optical fibres functioning as linear sensors. Temperatures are recorded along the optical sensor cable, thus not at points, but as a continuous profile. A high accuracy of temperature determination is achieved over great distances.
Measuring Principle - Raman Effect
Physical measurement dimensions, such as temperature or pressure and tensile forces, can affect glass fibres and locally change the characteristics of light transmission in the fibre. As a result of the attenuation of the light in the quartz glass fibres through scattering, the location of an external physical effect can be determined so that the optical fibre can be employed as a linear sensor.
Optical fibres are made from doped quartz glass. Quartz glass is a form of silicon dioxide (SiO2) with amorphous solid structure. Thermal effects induce lattice oscillations within the solid. When light falls onto these thermally excited molecular oscillations, an interaction occurs between the light particles (photons) and the electrons of the molecule. Light scattering, also known as
Raman scattering, occurs in the optical fibre. Unlike incident light, this scattered light undergoes a spectral shift by an amount equivalent to the resonance frequency of the lattice oscillation.
The light scattered back from the fibre optic therefore contains three different spectral shares:
- the Rayleigh scattering with the wavelength of the laser source used,
- the Stokes line components with the higher wavelength in which photons are generated, and
- the Anti-Stokes line components with a lower wavelength than the Rayleigh scattering, in which photons are destroyed.
The intensity of the so-called Anti-Stokes band is temperature-dependent, while the so-called Stokes band is practically independent of temperature. The local temperature of the optical fibre is derived from the ratio of the Anti-Stokes and Stokes light intensities.
Measuring Principle - OFDR Technology
Latest DTS evaluation units deploy the method of
Optical Frequency Domain Reflectometry (OFDR) . The OFDR system provides information on the local characteristic when the backscatter signal detected during the entire measurement time is measured as a function of frequency in a complex fashion, and then subjected to Fourier transformation. The essential benefits of OFDR technology are the quasi continuous wave mode employed by the laser and the narrow-band detection of the optical back scatter signal, whereby a significantly higher signal to noise ratio is achieved than with conventional pulse technology (OTDR). This technical benefit allows the use of affordable semiconductor laser diodes and electronic assemblies for signal averaging.
The optical frequency domain reflectometry has been developed as a high-resolution measurement process for the characterisation of optical wave guides with length dimensions of just a few millimetres. In contrast, its application for the Raman backscatter measurement was introduced and patented by the company LIOS Technology.
Schematic system set up
The temperature measuring system consists of a controller (frequency generator, laser source, optical module, HF mixer, receiver and micro-processor unit) and a quartz glass fibre (fibre optic) as line-shaped temperature sensor.
The design is three-channel, since an additional reference channel is required besides the two measurement channels (Anti-Stokes and Stokes). Corresponding to the OFDR system, the power output of the laser runs through the sinus-shaped frequency starting from a starting frequency in the kilohertz range through the ending frequency in the high megahertz range within a measurement time interval with the help of the High Frequency (HF) modulator. The resulting frequency shift is a direct measurement of the local resolution of the reflectometer. The frequency-modulated laser light is connected to the fibre optic-sensor via the optical module.
The continuously back-scattered Raman light is spectrally filtered in the optical module and converted into electrical signals by means of photo detectors. Then the measurement signals are amplified and mixed in the Low Frequency spectral range (LF range). The Fourier transformation of the averaged LF signals results in the two Raman backscatter curves. The amplitudes of these backscatter curves are proportional to the intensity of the Raman scattering of the viewed location. The fibre temperature along the sensor cable results from the amplitude ratio of the two measurement channels.
High Reliability and Industrial Strength
The semiconductor laser diode has been thoroughly type tested according the Telcordia GR-468 standard. It fulfils telecom standards with a medium lifetime of more than 25 years. The entire system was comprehensively evaluated by various independent international bodies (e.g. the VdS, the association of German asset insurers) including EMC tests as well as endurance tests at accelerated aging environments. Field data of the huge installed base prove the exceptional high reliability of the controllers.
Read more...
Tunnels are sensitive traffic bottlenecks and consequently extraordinary vulnerable in case of accidents or fire blasts. Danger for life and enormous economic consequences ask also for technical solutions of prevention and limitation of damage.